International Journal of Esthetic Dentistry (EN), 03/2024

Digital technologies are gradually gaining ground in dentistry. In particular, taking impressions with intraoral scanners is becoming routine; however, even this must often be preceded by the use of retraction cords. This article presents an innovative technique to record digital impressions of natural tooth abutments using interim restorations relined with impression material instead of retraction cords. In the laboratory, using computer-aided design, the technician can segment the internal surface of the interim restoration and use it to replace the abutment of the intraoral scan, thus obtaining an accurate coping that yields more detailed information about the supragingival and intrasulcular surface of the preparation. Palabras clave: cord, dental technology, digital impression, prosthodontics, retraction cord

In restorative dentistry, the lack of occlusal space may lead to the mutilation of healthy tissue in order to provide sufficient space for the restorative material. Noprep dentistry can be achieved by placing high-bite restorations, followed by Simple Orthodontic Extrusion (SOE) of other teeth to close the created open bite. This rapid, partial orthodontic treatment is well accepted by patients as it can be easily performed using simple buttons, and it takes only a few weeks to reestablish occlusal contacts. The SOE technique is a further development of the Dahl concept. It has the advantages without the disadvantages. Two applications of this technique are presented in this article: the treatment of the severe wear of anterior teeth with no-prep palatal veneers made of Polymer-infiltrated Ceramic Network (PICN, “hybrid ceramic”) material and the realization of no-prep zirconia resin-bonded bridges (RBBs) to replace missing lateral incisors. An original 3D-printed resin guide for correctly positioning RBBs and facilitating the removal of excess composite cement is also presented. This work highlights the considerable advantages of multidisciplinary collaboration in the field of minimally invasive dentistry. Palabras clave: hybrid ceramic, minimally invasive dentistry, occlusion, orthodontics, PICN, resin-bonded bridges, tooth wear, zirconia

Aim: The present study aims to describe an in-house protocol for fully guided zygomatic implant surgery and prosthesis repositioning. Materials and methods: Four extramaxillary zygomatic dental implants (ZIs) were placed in one patient. The preoperative phase included digital planning, through which a surgical guide was designed and created. The analysis of the accuracy of guided surgery and the guided prosthesis repositioning was carried out by superimposing the digital planning with the final postsurgical implant positioning through CBCT. The radiologic evaluation included implant angular deviation, entrance and exit deviation, platform deviation, and apex apicocoronal and mesiodistal deviation. The prosthetic evaluation was performed in three directions: buccopalatal, apicocoronal, and mesiodistal. Results: All the ZIs successfully osseointegrated after 3 months of healing, with no complications. The mean axial angular implant deviation was 0.52 ± 0.36 degrees, and the mean implant depth deviation was 0.47 ± 0.28 mm. The entrance and exit deviation of the implants was 0.74 ± 0.42 mm and 0.7 ± 0.43 mm, respectively. The virtual prosthesis was superimposed and compared with the standard tessellation language file of the provisional polymethyl methacrylate prosthesis at the level of the first molars and central incisors; the mean buccopalatal deviation was 0.6 ± 0.035 mm, the mean apicocoronal deviation was 0.65 ± 0.11 mm, and the mean mesiodistal deviation was 0.3 ± 0.07 mm. Conclusions: According to the results obtained in this first case of the present case series, careful and meticulous digital planning based on the correct prosthetic parameters can safely guide the performance of surgery. Palabras clave: implantology, prosthodontics

Aim: The objective of the present study was to investigate the association between the anatomical characteristics of different tooth groups and the diffusion and bleaching effect of hydrogen peroxide (H2O2). Materials and methods: Computed tomography (CT) images from five patients were used to assess the hard tissue thickness and pulp volume (PV) of four tooth groups: lower (mandibular) incisors (LI), upper (maxillary) incisors (UI), canines (C), and premolars (PM). Additionally, 80 bovine tooth disks were divided into four groups (n = 20) to match the thickness of each tooth group studied. All the specimens were exposed to a 35% H2O2 bleaching gel, with 50 µL applied for 45 min during the first, second, and third sessions. Diffusion was evaluated using the peroxidase enzyme method. Color change analyses (∆E, ∆E00, and ∆WID) were performed after the three application sessions and 7 days after the bleaching treatment using a spectrophotometer. Results: The PM group showed greater thickness and PV, followed by the C, UI, and LI groups (P 0.001). The LI group had six times greater H2O2 diffusion compared with the PM group (P 0.001), while the PM group exhibited a PV nine times larger than the LI group. Furthermore, the LI and UI groups achieved color saturation with one fewer session than the C and PM groups. Conclusions: Specific tooth groups have anatomical characteristics that interfere with bleaching treatment in terms of the diffusion and whitening effect of H2O2. Furthermore, the diffusion capacity of H2O2 was inversely proportional to the thickness of the tooth groups. Palabras clave: color change, dental pulp cavity, endodontics, restorative dentistry, tooth bleaching

Aim: The objective of the present study was to evaluate the influence of different adhesive strategies regarding shear bond strength (SBS) of provisional resin-­based materials bonded to the enamel surface as well as on the enamel surface roughness. Materials and methods: Bovine incisors were randomly divided into six groups (n = 10) according to the adhesive strategy used: BRControl (bis-acrylic resin); Spot-etch+BR (spot-etch + bis-acrylic resin); Spot-­etchSB2+BR (spot-etch + adhesive + bis-acrylic resin); Spot-etchZ350Flow+BR (spot-etch + flowable composite resin + bis-acrylic resin); SBU+BR (universal adhesive + bis-acrylic resin); Spot-etchSBMP+Z350 (spot-etch + adhesive + composite resin). The enamel surface roughness was determined by a surface profil­ometer. An SBS test was performed in a universal testing machine, and failure modes were classified under magnification. The SBS data were analyzed by one-way analysis of variance (ANOVA). A paired t test was used for enamel surface roughness intragroup comparisons, and the Friedman one-way repeated meas­ures analysis of variance by ranks was used for differences in enamel surface roughness between groups, with the Tukey post hoc test (a = 0.05). Results: BRControl had the lowest SBS values (MPa), with a significant difference (P ≤ 0.001) from the other groups. Spot-etch+BR had the highest SBS values but with no significant differences from the other groups in which the spot-etch technique was also used. Adhesive failure mode was predominant for all groups. BRControl had the lowest surface roughness difference, significantly different (P = 0.001) from all the other groups. Conclusions: Spot-etch and other adhesive strategies could be applied to increase the SBS values of provisional restorations to enamel compared with no surface pretreatment. However, the adhesive strategy may change the enamel surface roughness, revealing the importance of cleaning the tooth surface. Palabras clave: bisphenol A-glycidyl methacrylate, composite resin, dental esthetics, dental etching, dental materials, dental veneers, temporary dental restoration